Late last summer I ordered an ATS low profile chest rig, medical pouch,
and triple M4 magazine shingle.
I was looking at a couple different low profile platforms to carry a
couple extra rifle magazines / pistol magazines / medical supplies. I
wanted something that I could throw in my rifle bag for work.
At the time, the low profile chest rig was in the prototype stage and
featured (4) open top M4 magazine pouches (covered in 8 channels of PALS
webbing), an internal pocket, H-Harness shoulder strap.
I used the ATS Low Profile Chest Rig and Medical Pouch at Larry Vickers
Carbine course in September.
The low profile chest rig (prototype) has (4) M4 mag pouches that are
covered with 8 channels of PALS webbing. Each M4 mag pouch has an
elastic bungee strap to secure the magazine and the mag pouch is also
partially lined with a thin black rubber type material (Sure-Grip) that
assists with retention when the bungee strap is not in use.
Initially I was a little apprehensive about the Sure-Grip lined magazine
pouches. I thought the material may interfer with a smooth draw from the
pouch. During the Vickers carbine class and training with the chest rig
after the class, I had no problems accessing the magazines from the
pouch. The M4 magazine pouches had zero issues with fit or draw of
either USGI magazine or Magpul PMAGs.
The shoulder straps are made of 2" wide nylon webbing and the shoulder
strap is configured in a H-Harness design. The nylon straps were low
profile and comfortable. The only issue I had was horizontal strap that
connected the two shoulder straps in the back was a little too wide for
me. This was an easy fix, Darrin (Eggroll from
http://www.extremegearlabs.com
) was also attending the class and took the chest rig home one night
after class and simply folded over and stitched down some of the extra
material.
I think this platform would also lend it's self well to being used as a
bandoleer for active shooter situations for law enforcement or a
civilian who wanted to carry a few extra magazines in a rifle bag.
I really like the design of the ATS Medical pouch. The ATS Medical
Pouch looks like most other medical pouches I have used is a zippered
clam shell design, lined with elastic nylon strips inside to hold misc.
medical supplies. What sets the ATS Medical Pouch apart from other
designs that I have used is that ATS pouch is a "tear away" design.
The ATS pouch is a 2 part system, the base rectangular base that attaches
to a MOLLE chest rig / vest / body armor is lined with velcro and has a
flap that goes over the top of the pouch and a piece of webbing that
goes under the bottom of the pouch. The upper flap and bottom webbing
each contain a fastex buckle.
The Velcro and fastex equipped flap / webbing hold the medical pouch in
place. When access to the medical pouch is needed, simply disconnect
the fastex buckle which exposes a red pull tab attached to the medical
pouch, pull the tab to pull the Velcro backed medical pouch away from
the Velcro lined MOLLE base.
It is much easier to access the medical supplies you need when the pouch
is in your hand and you can see everything that is in the pouch, instead
of trying to get what you need when the pouch is still mounted to your
chest rig / body armor.
The ATS Triple M4 Mag Shingle is extremely robust in construction,
covered in 6 channels of PALS webbing, bungee cord for retention, and
ATS' own L-Strap MOLLE fasteners. I found the L-Strap fasteners much
more user friendly than other designs and very secure.
The pouches easily fit both USGI M4 magazines and Magpul PMAGs and the
bungee straps fit mags with or without Magpul Ranger Plates. Good
design, I really like it.
Low profile chest rig front (Tactical Tailor Triple
Pistol Mag Pouch and ATS Medical Pouch attached):

Low profile chest rig rear:

ATS Medical Pouch unbuckled:

ATS Medical Pouch removed from MOLLE carrier:

ATS Medical Pouch and Triple M4 Magazine Shingle on an
Eagle Ind. All MOLLE Chest Rig:

ATS Low Profile Chest Rig without any pouches attached: